IMPA Konik Pim El Raybaları 1/48 ürünleri yapılandırılmış deniz ikmal RFQ akışları için listelenmiştir; tedarik ekipleri kalemleri IMPA koduyla eşleştirebilir, miktarları toplayabilir ve tek bir toplu teklif talebi hazırlayabilir.
IMPA Konik Pim El Raybaları 1/48, ShipsBay kataloğunda yapılandırılmış teklif talebi akışları için 30 deniz ikmal ürününü bir araya getirir. Alıcılar doğru ürünü IMPA kodu veya ürün adıyla bulur, farklı departmanlardan miktarları toplar ve tek bir toplu teklif talebi gönderir. Her kayıt tarafsız biçimde tanımlanır; satış ekibi stok durumunu, teslim limanını ve ticari koşulları yanıtında doğrular.
Reamer Hand Straight Flute, 0.5x30mm
These reamers are driven by hand to finish the inside walls of drilled holes. To achieve an improved starting performance, the cutting edge is slightly chamfered. The flutes are normally straight and helical. Spiral flutes are recommended for operations involving an interruption to the cut, such as a keyway.
Reamer Hand Straight Flute, 0.8x35mm
These reamers are driven by hand to finish the inside walls of drilled holes. To achieve an improved starting performance, the cutting edge is slightly chamfered. The flutes are normally straight and helical. Spiral flutes are recommended for operations involving an interruption to the cut, such as a keyway.
Reamer Hand Straight Flute, 1.0x40mm
These reamers are driven by hand to finish the inside walls of drilled holes. To achieve an improved starting performance, the cutting edge is slightly chamfered. The flutes are normally straight and helical. Spiral flutes are recommended for operations involving an interruption to the cut, such as a keyway.
Reamer Hand Straight Flute, 1.2x45mm
These reamers are driven by hand to finish the inside walls of drilled holes. To achieve an improved starting performance, the cutting edge is slightly chamfered. The flutes are normally straight and helical. Spiral flutes are recommended for operations involving an interruption to the cut, such as a keyway.
Reamer Hand Straight Flute, 1.5x50mm
These reamers are driven by hand to finish the inside walls of drilled holes. To achieve an improved starting performance, the cutting edge is slightly chamfered. The flutes are normally straight and helical. Spiral flutes are recommended for operations involving an interruption to the cut, such as a keyway.
Reamer Hand Straight Flute, 1.8x55mm
These reamers are driven by hand to finish the inside walls of drilled holes. To achieve an improved starting performance, the cutting edge is slightly chamfered. The flutes are normally straight and helical. Spiral flutes are recommended for operations involving an interruption to the cut, such as a keyway.
Reamer Hand Straight Flute, 2.0x60mm
These reamers are driven by hand to finish the inside walls of drilled holes. To achieve an improved starting performance, the cutting edge is slightly chamfered. The flutes are normally straight and helical. Spiral flutes are recommended for operations involving an interruption to the cut, such as a keyway.
Reamer Hand Straight Flute, 2.2x60mm
These reamers are driven by hand to finish the inside walls of drilled holes. To achieve an improved starting performance, the cutting edge is slightly chamfered. The flutes are normally straight and helical. Spiral flutes are recommended for operations involving an interruption to the cut, such as a keyway.
Reamer Hand Straight Flute, 2.5x65mm
These reamers are driven by hand to finish the inside walls of drilled holes. To achieve an improved starting performance, the cutting edge is slightly chamfered. The flutes are normally straight and helical. Spiral flutes are recommended for operations involving an interruption to the cut, such as a keyway.
Reamer Hand Straight Flute, 2.8x65mm
These reamers are driven by hand to finish the inside walls of drilled holes. To achieve an improved starting performance, the cutting edge is slightly chamfered. The flutes are normally straight and helical. Spiral flutes are recommended for operations involving an interruption to the cut, such as a keyway.
Reamer Hand Straight Flute, 3.0x72mm
These reamers are driven by hand to finish the inside walls of drilled holes. To achieve an improved starting performance, the cutting edge is slightly chamfered. The flutes are normally straight and helical. Spiral flutes are recommended for operations involving an interruption to the cut, such as a keyway.
Reamer Hand Straight Flute, 3.5x75mm
These reamers are driven by hand to finish the inside walls of drilled holes. To achieve an improved starting performance, the cutting edge is slightly chamfered. The flutes are normally straight and helical. Spiral flutes are recommended for operations involving an interruption to the cut, such as a keyway.
Reamer Taper Pin American, Standard Straight Flute #0
1/48 Taper pins according to U.S. Standard have a taper of 6.35 mm per 25.4 mm. These reamers are designed in nominal numbers but since the standards are not unified, there are minor differences in tip diameter and small end diameter.
Reamer Taper Pin American, Standard Straight Flute #00
1/48 Taper pins according to U.S. Standard have a taper of 6.35 mm per 25.4 mm. These reamers are designed in nominal numbers but since the standards are not unified, there are minor differences in tip diameter and small end diameter.
Reamer Taper Pin American, Standard Straight Flute #000
1/48 Taper pins according to U.S. Standard have a taper of 6.35 mm per 25.4 mm. These reamers are designed in nominal numbers but since the standards are not unified, there are minor differences in tip diameter and small end diameter.
Reamer Taper Pin American, Standard Straight Flute #0000
1/48 Taper pins according to U.S. Standard have a taper of 6.35 mm per 25.4 mm. These reamers are designed in nominal numbers but since the standards are not unified, there are minor differences in tip diameter and small end diameter.
Reamer Taper Pin American, Standard Straight Flute #1
1/48 Taper pins according to U.S. Standard have a taper of 6.35 mm per 25.4 mm. These reamers are designed in nominal numbers but since the standards are not unified, there are minor differences in tip diameter and small end diameter.
Reamer Taper Pin American, Standard Straight Flute #10
1/48 Taper pins according to U.S. Standard have a taper of 6.35 mm per 25.4 mm. These reamers are designed in nominal numbers but since the standards are not unified, there are minor differences in tip diameter and small end diameter.
Reamer Taper Pin American, Standard Straight Flute #11
1/48 Taper pins according to U.S. Standard have a taper of 6.35 mm per 25.4 mm. These reamers are designed in nominal numbers but since the standards are not unified, there are minor differences in tip diameter and small end diameter.
Reamer Taper Pin American, Standard Straight Flute #13
1/48 Taper pins according to U.S. Standard have a taper of 6.35 mm per 25.4 mm. These reamers are designed in nominal numbers but since the standards are not unified, there are minor differences in tip diameter and small end diameter.
Reamer Taper Pin American, Standard Straight Flute #14
1/48 Taper pins according to U.S. Standard have a taper of 6.35 mm per 25.4 mm. These reamers are designed in nominal numbers but since the standards are not unified, there are minor differences in tip diameter and small end diameter.
Reamer Taper Pin American, Standard Straight Flute #2
1/48 Taper pins according to U.S. Standard have a taper of 6.35 mm per 25.4 mm. These reamers are designed in nominal numbers but since the standards are not unified, there are minor differences in tip diameter and small end diameter.
Reamer Taper Pin American, Standard Straight Flute #3
1/48 Taper pins according to U.S. Standard have a taper of 6.35 mm per 25.4 mm. These reamers are designed in nominal numbers but since the standards are not unified, there are minor differences in tip diameter and small end diameter.
Reamer Taper Pin American, Standard Straight Flute #4
1/48 Taper pins according to U.S. Standard have a taper of 6.35 mm per 25.4 mm. These reamers are designed in nominal numbers but since the standards are not unified, there are minor differences in tip diameter and small end diameter.
